CK1000 Series สัญญาณแจ้งเตือนไฟไหม้

General
AC POWER : 90 to 270VAC, 50 Hz, 3.0 amps.
Wire size : minimum 14 AWG (2.0 mm2) with 600-volt insulation.
BATTERY : Sealed lead-acid batteries only.
Maximum charging circuit: 27.6VDC @ 0.8 amp for normal flat charge.
Maximum battery charger capacity : 18AH battery.

Specifications
AC POWER : 90 to 270VAC, 50 Hz, 3.0 amps.
Wire size : minimum 14 AWG (2.0 mm2) with 600-volt insulation.
BATTERY : Sealed lead-acid batteries only.
Maximum charging circuit : 27.6VDC @ 0.8 amp for normal flat charge.
Maximum battery charger capacity : 18AH battery.

Features
Four to Sixteen Style B (Class B) Initiating Device Circuits (IDCs). All zones accept two-wire smoke detectors and any normallyopen contact devices. Zones 1 - 16 configured as general alarm zones. All circuits are power-limited and supervised, meeting the latest ULC requirements using fuseless technology. Two built-in, Style Y (Class B) Notification Appliance (Signal) Circuits (NACs). NACs may be programmed: Silenceable, Non-Silenceable, Auto-Silence 1.25 amps of NAC power. 3.00 amps of total system power. Alarm, Trouble and Supervisor, relay output. 24 volt operation. Resettable four-wire smoke detector power @ 500 mA. Nonresettable power @ 500 mA. Integral battery charger capable of charging up to 18 AH batteries (batteries over 4 AH require use of the external battery backbox, or ULC listed equivalent). Disable/Enable control per IDC. Reverse polarity protection. The CK1000 Series Conventional Fire Alarm Control Panel is a 24 volt, four, eight, sixteen-zone, Class B, Conventional Fire Alarm Control Panel. Designed exclusively to meet the latest market requirements and future ULC codes, the highly costeffective CK1000 Series can be used in a variety of low- to midsized applications.

HC102
Conventional Manual Call Point
Operating Voltage Range : 9～28VDC Volts
Alarm Current : 45 mA @ 24 VDC
Operating Humidity Range :10% to 93% Relative Humidity, Non-condensing
Operating Temperature Range : -10°C to 50°C (14°F to 122°F)
Dimensions : Length 140mm, Width 105mm, Depth 45mm
Weight : Net Weight 220g

SB106
Conventional Manual Call Point

• Compatible with all the conventional fire alarm control panel
• Can be reset by key
• 470 Ohm resistance
• Easy surface mounting Base included

SG109
Conventional Sound Strobe

• Compatible with all the conventional fire alarm control panel
• Long light life up to 40000 flahsed
• High sound level up to 100dB

JL188-6"/8"/10"
Conventional Alarm Bell

• Three module size of 6", 8", 10'
• Compatible with all the conventional fire alarm control panel
• High sound level up to 95dB
• Easy installation bracket included
• Steel material

WT105C
Conventional Heat Detector

• Compatible with all the conventional fire alarm control panel
• Unpolarized wire input
• Wide range of operating voltages
• High precision electronic thermistor
• Built in microprocessor intelligent software
• Two LEDs blink standby, provide 360° visibility
• Insect-resistant screening
• Twist-on mounting base with tamper lock
• Remote Indicator LED can be connected.

YT102C
Conventional Smoke Detector

• Compatible with all the conventional fire alarm control panel
• Unpolarized wire input
• Wide range of operating voltages
• Unique optical sensing chamber
• Built in microprocessor intelligent software
• Two LEDs blink standby, provide 360° visibility
• Insect-resistant screening
• Twist-on mounting base with tamper lock
• Drift compensation and smoothing algorithms
• Remote Indicator LED can be connected.

FT103
Conventional Smoke & Heat Detector

• Compatible with all the conventional fire alarm control panel
• Unpolarized wire input
• Wide range of operating voltages
• Unique optical sensing chamber and High precision electronic thermistor
• Built in microprocessor intelligent software
• Two LEDs blink standby, provide 360° visibility
• Insect-resistant screening
• Twist-on mounting base with tamper lock
• Drift compensation and smoothing algorithms
• Remote Indicator LED can be connected.